You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
83 lines
2.1 KiB
Plaintext
83 lines
2.1 KiB
Plaintext
# For more options and information see
|
|
# http://rpf.io/configtxt
|
|
# Some settings may impact device functionality. See link above for details
|
|
|
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
|
#hdmi_safe=1
|
|
|
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
|
# goes off screen, and negative if there is too much border
|
|
#overscan_left=16
|
|
#overscan_right=16
|
|
#overscan_top=16
|
|
#overscan_bottom=16
|
|
|
|
# uncomment to force a console size. By default it will be display's size minus
|
|
# overscan.
|
|
#framebuffer_width=1280
|
|
#framebuffer_height=720
|
|
|
|
# uncomment if hdmi display is not detected and composite is being output
|
|
hdmi_force_hotplug=1
|
|
hdmi_ignore_cec=1
|
|
hdmi_ignore_cec_init=1
|
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
|
hdmi_group=1
|
|
hdmi_mode=4
|
|
|
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
|
# DMT (computer monitor) modes
|
|
#hdmi_drive=2
|
|
|
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
|
# no display
|
|
#config_hdmi_boost=4
|
|
|
|
# uncomment for composite PAL
|
|
#sdtv_mode=2
|
|
|
|
#uncomment to overclock the arm. 700 MHz is the default.
|
|
#arm_freq=800
|
|
|
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
|
#dtparam=i2c_arm=on
|
|
#dtparam=i2s=on
|
|
#dtparam=spi=on
|
|
|
|
# Uncomment this to enable infrared communication.
|
|
#dtoverlay=gpio-ir,gpio_pin=17
|
|
#dtoverlay=gpio-ir-tx,gpio_pin=18
|
|
|
|
# Additional overlays and parameters are documented /boot/overlays/README
|
|
|
|
# Enable audio (loads snd_bcm2835)
|
|
dtparam=audio=on
|
|
|
|
# Automatically load overlays for detected cameras
|
|
camera_auto_detect=1
|
|
|
|
# Automatically load overlays for detected DSI displays
|
|
display_auto_detect=1
|
|
|
|
# Enable DRM VC4 V3D driver
|
|
dtoverlay=vc4-fkms-v3d
|
|
max_framebuffers=2
|
|
|
|
# Disable compensation for displays with overscan
|
|
disable_overscan=1
|
|
|
|
[cm4]
|
|
# Enable host mode on the 2711 built-in XHCI USB controller.
|
|
# This line should be removed if the legacy DWC2 controller is required
|
|
# (e.g. for USB device mode) or if USB support is not required.
|
|
otg_mode=1
|
|
|
|
[all]
|
|
|
|
[pi4]
|
|
# Run as fast as firmware / board allows
|
|
arm_boost=1
|
|
|
|
[all]
|
|
gpu_mem=128
|